IGRP STUB區域設置了之後，路由器在丟失路由條目的時候不會向 STUB區域發查詢消息，在上述top中我們可以把Rc做成 STUB區域，假如Rb的loop0 口down掉了之後，Rb不會向Rc發送查詢消息。下面是小編帶來的實例，歡迎學習!
我們先在這3太路由器上全部啓用EIGRP 10 ，所有的.接口都參與到EIGRP 10 在沒有設置stub的時候，得到路由表如下：
RA：
is subnetted, 1 subnets
C is directly connected, Loopback0
is subnetted, 1 subnets
D [90/2297000] via , 00:01:26, Serial2/1
is subnetted, 1 subnets
D [90/2297000] via , 00:00:37, Serial2/1
is subnetted, 1 subnets
D [90/2297000] via , 00:01:26, Serial2/1
is subnetted, 1 subnets
C is directly connected, Serial2/1
Rb：
is subnetted, 1 subnets
D [90/2297000] via , 00:02:30, Serial2/1
is subnetted, 1 subnets
C is directly connected, Loopback0
is subnetted, 1 subnets
D [90/2297000] via , 00:01:41, Serial2/2
is subnetted, 1 subnets
C is directly connected, Serial2/2
is subnetted, 1 subnets
C is directly connected, Serial2/1
Rc:
is subnetted, 1 subnets
D [90/2297000] via , 00:02:06, Serial2/2
is subnetted, 1 subnets
D [90/2297000] via , 00:02:06, Serial2/2
is subnetted, 1 subnets
C is directly connected, Loopback0
is subnetted, 1 subnets
C is directly connected, Serial2/2
is subnetted, 1 subnets
D [90/2297000] via , 00:02:06, Serial2/2
下面，我們開始試驗，在Rc上沒有設置stub的時候，在Rb上打開debug
RB#debug eigrp packets query
RB EIGRP Packets debugging is on
(QUERY)
RB#config t
Enter configuration commands, one per line. End with CNTL/Z.
RB(config)#
RB(config)#int loopback 0
RB(config-if)#shu
*Mar 1 00:16:38.587: EIGRP: Enqueueing QUERY on Serial2/1 iidbQ un/rely 0/1 serno 6-6
*Mar 1 00:16:38.591: EIGRP: Enqueueing QUERY on Serial2/1 nbr iidbQ un/rely 0/0 peerQ un/rely 0/0 serno 6-6
*Mar 1 00:16:38.599: EIGRP: Sending QUERY on Serial2/1 nbr (向RA發送查詢)
*Mar 1 00:16:38.603: AS 10, Flags 0x0, Seq 10/3 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1 serno 6-6
*Mar 1 00:16:38.607: EIGRP: Enqueueing QUERY on Serial2/2 iidbQ un/rely 0/1 serno 6-6
*Mar 1 00:16:38.611: EIGRP: Enqueueing QUERY on Serial2/2 nbr iidbQ un/rely 0/0 peerQ un/rely 0/0 serno 6-6
*Mar 1 00:16:38.619: EIGRP: Sending QUERY on Serial2/2 nbr (向RC發送查查詢)
*Mar 1 00:16:38.623: AS 10, Flags 0x0, Seq 11/3 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1 serno 6-6
可以看到，沒有設置stub的時候 Rb會向RA和 Rc發送查詢消息。下面我們把Rc做成 STUB區域.
我們先把RB上的loopback 0 打開，讓網絡回到正常的收斂
Rb(config-it)# int lo 0
Rb(config-it)#no sh
然後把RC設置成STUB區域
RC(config)#router ei 100
RC(config-router)#eigrp stub receive-only
再關掉RB上的loopback 0
再來看RB的查詢情況：
*Mar 1 00:28:13.139: EIGRP: Enqueueing QUERY on Serial2/2 iidbQ un/rely 0/1 serno 9-9
*Mar 1 00: 28:13.143: EIGRP: Enqueueing QUERY on Serial2/2 nbr iidbQ un/rely 0/0 peerQ un/rely 0/0 serno 9-9
*Mar 1 00: 28:13.151: EIGRP: Enqueueing QUERY on Serial2/1 iidbQ un/rely 0/1 serno 9-9
*Mar 1 00: 28:13.155: EIGRP: Enqueueing QUERY on Serial2/1 nbr iidbQ un/rely 0/0 peerQ un/rely 0/0 serno 9-9
*Mar 1 00: 28:13.163: EIGRP: Sending QUERY on Serial2/1 nbr (向RA發送查詢)
*Mar 1 00: 28:13.163: AS 10, Flags 0x0, Seq 19/8 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1 serno 9-9
*Mar 1 00: 28:13.351: EIGRP: Received QUERY on Serial2/2 nbr
RB(config-if)#
*Mar 1 00: 28:13.355: AS 10, Flags 0x0, Seq 11/21 idbQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/0
自始至終沒有發現去往Rc的查詢消息，所以，EIGRP的 STUB區域驗證成功。
